近10年中国三大经济区太阳总辐射特征及其与O3、PM2.5的关系

采用中国地面气象观测站网2007~2016年的辐射日值数据集和中国空气质量在线监测平台2014~2016年逐日观测数据,分析了京津冀、长三角和珠三角近10a太阳总辐射年际和季节变化,近3a臭氧日最大8h平均（O_{3_8h_max}）和细颗粒物（PM_2.5）的污染过程频次变化,通过不同因子及其不同强度等级的分型统计,探讨PM_2.5、O_{3_8h_max}与太阳总辐射的关系.结果表明：京津冀近10a太阳总辐射显著上升,京津冀春季和珠三角夏季太阳总辐射显著上升.三大经济区PM_2.5污染过程年频次均呈现逐年递减,且从北到南递减;O₃污染过程年频次时间上呈现先减后增,空间上京津冀多于长三角和珠三角.三大经济区O_{3_8h_max}与太阳总辐射相关系数均在0.71以上,有较强的正相关;而PM_2.5与太阳总辐射的相关性具有区域差异性.三大经济区不同季节不同太阳总辐射下O_{3_8h_max}与PM_2.5的相关关系差异显著,其中京津冀春夏秋三季O_{3_8h_max}与PM_2.5在强太阳总辐射下有较好的正相关,冬季则存在一定的负相关;长三角四季两者相关性均较弱;珠三角夏季两者正相关最为显著;不同PM_2.5浓度下O_{3_8h_max}与太阳总辐射的线性拟合效果较好,体现出较强的正相关关系,各经济区拟合曲线的倾向率均随PM_2.5升高而增大.PM_2.5>75μg/m³时拟合优度均达到最大.     

牛粪-化肥配施对水稻田氮磷迁移转化的影响

在控制外源N输入量相同的前提下,通过田间小区实验,探讨有机肥与化肥不同施用量（牛粪施用量：5,10,20t/hm²）对稻田田间土-水界面氮磷迁移转化特征的影响.结果表明：控制稻田水中NH₄⁺-N、NO₃^--N、TN和TP输出的最佳时期分别为施肥后的第5,30,7,20d,且TN和TP浓度随时间变化符合单指数衰减方程（0.7444≤R²≤0.9724;1.1×10^-6≤F≤0.0055）.采用牛粪部分代替化肥的施肥方式,在一定范围内能降低稻田退水中TN、TP输出负荷（41.8%、36.0%、64.3%;20.3%、39.1%、48.9%）,还可以降低稻田水中N/P,降低水体富营养化风险.同时,牛粪的施用可提高土壤中脲酶和磷酸酶的含量,促进氮磷向植物可吸收形态转化.综合经济成本和生态效益核算,采用10t有机肥代替无机肥的处理是相对经济环保的施肥方法,该施肥方式下,氮磷年输出负荷分别为17.70,1.26kg/hm².     

Potential of secondary aerosol formation from Chinese gasoline engine exhaust

Light-duty gasoline vehicles have drawn public attention in China due to their significant primary emissions of particulate matter and volatile organic compounds(VOCs). However,little information on secondary aerosol formation from exhaust for Chinese vehicles and fuel conditions is available. In this study, chamber experiments were conducted to quantify the potential of secondary aerosol formation from the exhaust of a port fuel injection gasoline engine. The engine and fuel used are common in the Chinese market, and the fuel satisfies the China V gasoline fuel standard. Substantial secondary aerosol formation was observed during a 4–5 hr simulation, which was estimated to represent more than 10 days of equivalent atmospheric photo-oxidation in Beijing. As a consequence, the extreme case secondary organic aerosol(SOA) production was 426 ± 85 mg/kg-fuel, with high levels of precursors and OH exposure. The low hygroscopicity of the aerosols formed inside the chamber suggests that SOA was the dominant chemical composition. Fourteen percent of SOA measured in the chamber experiments could be explained through the oxidation of speciated single-ring aromatics. Unspeciated precursors, such as intermediate-volatility organic compounds and semi-volatile organic compounds, might be significant for SOA formation from gasoline VOCs. We concluded that reductions of emissions of aerosol precursor gases from vehicles are essential to mediate pollution in China.     

Effect of TiO2 nanoparticle aggregation on marine microalgae Isochrysis galbana

TiO_2 nanoparticles(NPs) could adversely impact aquatic ecosystems. However, the aggregation of these NPs could attenuate this effect. In this work, the biological effects of TiO_2 NPs on a marine microalgae Isochrysis galbana were investigated. The aggregation kinetics of TiO_2 NPs under different conditions was also investigated to determine and understand these effects. Results showed that, though TiO_2 NPs had no obvious impact on the size and reproducibility of algal cells under testing conditions, they caused a negative effect on algal chlorophyll, which led to a reduction in photosynthesis. Furthermore, fast aggregation of TiO_2 NPs occurred under all conditions, especially at the pH close to the p Hzpc. Increasing ionic strength and NP concentration also enhanced the aggregation rate.The aggregation and the following sedimentation of TiO_2 NPs reduced their adverse effects on I. galbana.     

水环境综合整治工程存在的风险因素分析研究

水环境综合整治工程存在的风险因素主要有财务风险、造价预测偏离风险、征地困难风险、施工事故风险以及后期质量可靠性风险等,根据风险因素构建评价解释变量和控制变量模型,结合内部控制和信息披露方法进行风险预测评估,采用分组样本检验方法进行水环境综合整治工程风险因素方法,采用T检验方法进行水环境质量可靠性检验,实现风险有效评估和预防。通过实证分析方法进行模板数据分析,提高对水环境综合整治工程存在的风险因素的定量评估能力。     

某型飞机外翼5—8肋损伤原因分析及修复探讨

目的 分析某型飞机外翼5—8肋油箱区结构不同程度损伤的原因,制定修复方案。方法采用受载分析、有限元仿真计算、静力试验数据分析等强度计算方法分析损伤产生的原因,采用扫描电子显微镜和光学显微镜对磨痕形貌进行观测等失效分析,对损伤结构件开展失效模式分析,根据损伤原因及失效模式制定科学简便的修复方案,同时对损伤长桁采取的修补措施进行强度校核。结果 通过对外翼油箱充压破坏理论分析、有限元仿真计算、静力试验数据反推,并结合飞机实际损伤情况,得出油箱破坏理论分析危险薄弱部位与真实破坏情况一致的结论。有限元仿真计算最危险结构部位与实际结构首先发生破坏部位吻合,可作为深入制定修复方案及推测实际加载压力的依据。通过静力试验数据反推、结构实际损伤及有限元仿真计算结论得出,外翼5—8肋结构出现损伤时油箱施加压力约0.5 MPa,针对损伤制定了更换外翼油箱内部第5—8肋损伤结构和贴补加强损伤长桁的修理方案,经结构强度校核,满足设计要求。结论 分析认为外翼5—8肋油箱区结构损伤原因为油箱压力超过设计值导致结构过载断裂,采用贴补加强修理损伤长桁和更换第5—8肋损伤结构的修复方案能够满足强度设计要求,可指导同类飞机类似结构损伤故障的原因分析和修理,提醒同类飞机维修人员在飞机维护时应关注外翼油箱压力超压问题。     

爆炸螺栓分离对热防护系统冲击响应分析

目的考察在爆炸螺栓分离过程中,作用在TPS(热防护系统)上的冲击响应是否会导致其破坏,从而影响航天器飞行安全,对过程进行数值仿真分析。方法提出四阶段仿真方案,基于MSC.Dytran软件,采用流固耦合方法对爆炸螺栓分离过程进行动力学仿真;根据单个爆炸螺栓地面分离试验的结构进行建模和分析,获取结构响应曲线;再根据实测的冲击响应数据,对爆炸过程中炸药及JWL方程的参数等设置进行调整,获取准确爆炸螺栓的分析模型;最后应用于对真实结构中TPS(热防护系统)在分离过程里受爆炸螺栓冲击响应的动力学分析与评估。结果通过参数调整,获得的仿真模型与爆炸螺栓地面分离试验实测结果一致,证明了仿真模型的有效性和四阶段仿真方案的可行性。结论提取的真实结构爆炸螺栓分离过程中作用在TPS(热防护结构)上的最大加速度响应曲线,可用于指导TPS(热防护系统)的设计。     

重庆九龙坡城区和城郊大气污染物浓度特征研究

为了解重庆市九龙坡区城区和城郊大气污染物浓度特征,分析了城区和城郊国控空气站点2014年3月~2015年2月典型污染物的浓度变化。结果表明,除O_3表现出夏高冬低的季节变化趋势外,其它污染物均表现出冬高夏低的季节变化趋势。PM_(2.5)污染最严重,城区和郊区日均值超标率分别为31.4%和33.4%。城区和城郊的PM_(2.5)浓度之间没有显著性差异(p0.05),城郊O_3浓度显著高于城区(p0.01),NO_2、SO_2、CO和PM_(10)则是城区显著高于城郊(p0.01)。     

大气环境质量综合评价加权灰色关联模型的建立与应用

利用灰色理论建立大气环境质量综合评价加权灰色关联模型 ,运用污染贡献率确定权重系数。与其它评价模型相比 ,加权灰色关联模型还具有排序功能 ,实例表明该模型是简便有效的     

Suggested protocol for collecting, handling and preparing peat cores and peat samples for physical, chemical, mineralogical and isotopic analyses

For detailed reconstructions of atmospheric metal deposition using peat cores from bogs, a comprehensive protocol for working with peat cores is proposed. The first step is to locate and determine suitable sampling sites in accordance with the principal goal of the study, the period of time of interest and the precision required. Using the state of the art procedures and field equipment, peat cores are collected in such a way as to provide high quality records for paleoenvironmental study. Pertinent field observations gathered during the fieldwork are recorded in a field report. Cores are kept frozen at -18 degree C until they can be prepared in the laboratory. Frozen peat cores are precisely cut into 1 cm slices using a stainless steel band saw with stainless steel blades. The outside edges of each slice are removed using a titanium knife to avoid any possible contamination which might have occurred during the sampling and handling stage. Each slice is split, with one-half kept frozen for future studies (archived), and the other half further subdivided for physical, chemical, and mineralogical analyses. Physical parameters such as ash and water contents, the bulk density and the degree of decomposition of the peat are determined using established methods. A subsample is dried overnight at 105 degree C in a drying oven and milled in a centrifugal mill with titanium sieve. Prior to any expensive and time consuming chemical procedures and analyses, the resulting powdered samples, after manual homogenisation, are measured for more than twenty-two major and trace elements using non-destructive X-Ray fluorescence (XRF) methods. This approach provides lots of valuable geochemical data which documents the natural geochemical processes which occur in the peat profiles and their possible effect on the trace metal profiles. The development, evaluation and use of peat cores from bogs as archives of high-resolution records of atmospheric deposition of mineral dust and trace elements have led to the development of many analytical procedures which now permit the measurement of a wide range of elements in peat samples such as lead and lead isotope ratios, mercury, arsenic, antimony, silver, molybdenum, thorium, uranium, rare earth elements. Radiometric methods (the carbon bomb pulse of (14)C, (210)Pb and conventional (14)C dating) are combined to allow reliable age-depth models to be reconstructed for each peat profile.